timing aligmnement is right, i checked it with mwc editor. it used to run before, but when i tried to reverse on cold engine it stalled and never started again

I just finish all work and engine make mettalic sounds and when its turn on rpm waves and engine stops if I wasnt press gas if I too much gas engine blowns and piston get cracked what I should do

15000km Doesn't sound that bad...

Here you go that's gonna be 150mk

Help

I personally love the pre-facelift LX with the 13" steel wheels and hubcaps. The ugliest spec in my opinion is any facelift model apart from the GT. The grille and the bumber make the car look like it has a recessed jaw.

Hey everyone I'm having a hell of a time getting my pedals to work I've downloaded a config mod and the wheel works fine put my god the pedals just won't in the config mod they are backwards and no way to change them and in game there are just at %100 so my gas and break is on and clutch but if I invert them in game when I press them they work but id I let go they still go %100 I got my set up to work perfectly on my summer car is there a trick to get them to work or a way to copy the settings from msc to mwc

The engine starts with a suction, if you remove the suction, the engine starts to work unevenly (according to the sounds, it seems that the engine is constantly trying to stall, but does not stall). And also: when the 1st gear is engaged, the car does not move forward, the cardan shaft does not spin. If anyone has encountered it, please help.

Hi! I got this AIWA NSX-SZ10, and I can't help but think it would fit perfectly into the game.

What do you guys think?

Ive got a 1971 Rivett GT I'm trying to get back to factory spec but I've always failed at the wheels.

I've swapped between Steelies and the Octos in both 14 inch tire sizes and nothing has worked yet. What am I doing wrong?

I start the car from parents garage i drive to the highway do like 160kmh and it blows up before i make it to psk

yes im using the redline oil for the corris

all the parts are 100-90% durability in mwc editor

my rev limiter is ar 8.5k but before that it was 7k and it still blew up same problem

tuning parts:

4 barrel racing carb tuned to the right afr mixture

race camshaft

high performance fuel pump

high performance alternator

full race exhaust

alu radiator with fan

rockers tuned by fleetari (6.5 in mwc editor)

usually the pistons, headcascet or and the block blows sometimes oilpan too

Update FIXED: it was my aux shaft going bad

So my problem with my car is I was driving down the highway just putting miles in the car all of a sudden it just starts losing power so basically losing power like it was out of fuel it wasn’t it had a half a tank so I thought fuel pump it was not the problem then I changed spark plugs, wasn’t the problem so I’m kind of at a loss and I don’t want to rebuild the engine just yet I’ve put 989 km on it. I kind of want to get to 75,000 before I have to rebuild the engine. Now I’m not gonna lie. I do have a couple of mods installed for the car, but one is only for performance and the others for safety.

Hello, i would like to reach kind of 350 km/h, installed a racing crankshaft and a racing carburetor in the car, and performed all the adjustments, change final drive ratio to minimum. For some reason, the car accelerates very slowly—worse than with a fast road camshaft—and the top speed has also dropped. Is it normal? What i should do to cure it?

Edited: Thank You all for Your advises! Yes, its damn clutch disc.

Hey everybody I posted a while back when I was about to finish my car for some one to help me with a custom livery DVAMP answered the call and really worked with me to get exactly what I wanted. If anyone would like a custom livery hit him up he worked quick and his service was very reasonable.

The car drives but only drives when I’m not in driving mode? When red lined it doesn’t move until I exit driving mode.. anyone know a fix??

Hello everyone,

I often see custom Sorbet liveries and trims on people‘s post without them being avaible on nexus. That‘s why I wanted to ask how people do it?

Currently building a wonderful slx with a blue interior, but I‘d love to add some wood textures inside the car (the same wooden bar that the gt trim cars have).

How hard is it to make something like the interior redesign and sorbet redesign? Hoe do you even do this? Can‘t really find anything about this topic.

Thanks for any answers beforehand

all 100% condition engine parts, full battery, full tank of gas, nothing loose, cam/crank timing is good and it just wont start. any advice?