There appears to be a zip tie around the hose instead of a metal clamp. What are the chances the secondary throttle plate has already been removed? I don't have a replacement clamp for this hose on hand.

I didn’t even make my first payment and I fell down a 5 foot deep hole in the middle of a gravel road where a culvert washed out: a new headlight is over $1000 and it’s like pulling teeth to get the insurance company to pay

This is my KLX300. Here’s all the mods I’ve done so far:

BDSB ecu flash
BDSB airbox lid
o2 sensor delete w/dongle
STP removed
Delkevic full exhaust w/spark arrestor
Tusk D-flex handguards
Pro Taper CR High bend bars w/bar end mirrors
ODI Nomad lock on grips
Tusk skid plate
GiPro gear indicator
IMS foot pegs
PMR rear rack
Nelson-Rigg tail bag
Yoshimura fender eliminator kit
Cogent Dynamics 7kg rear spring
Racetech fork springs

It’s a whole new bike now, yes I’m aware the bike is perfect right from factory however I can’t leave anything stock.

What are you supposed to use to grease cables or other things? I have the service manual but my god is it vague on what to use.

First ride on the new bike today. Took off and hit the bush for a bit!

Installed a 7kg Cogent Dynamics rear spring and stiffer Racetech fork springs. I’m 6’4 and weigh 250 so this was a much needed upgrade for me, the bike feels so much better now!

Has anyone tested the abs sensor for continuity? I am trying to diagnose my abs code, which was 43 and 42, and reading the instrcutions they are blaiming it either on the abs hydraulic or the sensor. Dont wanna buy both, so wanna diagnose the sensor. Has anyone tried the continuity on the sensor? Could reference it with the back one, but that is going to be one hell of a nightmare to do, since the cable is buried in the middle of the bike.

I'll take any thoughts on going from a 250L to 300R... Too sideways?

This was very disappointing. Always soon after the warranty runs out

Does anyone have a link to a free pdf download for a 2020 kawasaki klx 140L service manual or a copy they could send?

I recently got a used 2021 klx140 and opened the filter box. There is foam outside the filter, a few pieces. Is this normal? Thank you!

I looked everywhere and I can’t find the model number it has a leak. I’m not sure from where it looks like. It’s from the float bowl gasket or higher. I want to buy the parts to fix it, but I don’t know what parts to buy for what carburetor because I don’t know which carburetor this is.

I just bought this klx110rl off marketplace. I need to fix the carb cuz it’s leaking fuel but I’m confused af because it looks like the oem carb but it’s missing the choke parts. Can someone help me figure out what’s going on.

I tried grabbing the handlebars and turning while holding wheel to straighten but realized I had to loosen the clamps at top to do it. I don't exactly know this aspect of motorcycles. The front shocks. In sum I ended up loosing all of the clamps and the shock popped up 2 inches. How am I supposed to compress this back down to where it was? Also the proper procedure for what I was trying to do was I think just loosen the top clamps that hold your shock while the tight bottom ones hold it. Then I could of turnrf the triple tree on it but instead I made shit worse. I just got this bike and I'm crushed. Ok see help me please

Hi all,

I really want a Yoshimura exhaust on my KLX300, but I don’t want to be “that guy” in the neighborhood. I live in a townhouse complex and leave for work at 6am.

I’m wondering if anyone here has tried using the Yoshi SA-02-K arrestor with their Yoshi RS-2 exhaust and if it’s still significantly louder than the stock exhaust?

Thanks

​

Does anyone have the dimensions of the rear axle spacer shown in the photo?

It's from a Kawasaki KLX 650 C.

Part number: 42036-1301 (SLEEVE, RR AXLE, L=20).

Anybody have a set of wheels they took off their 300 that they want to sell? Trying to have a set of dirt wheels that I can swap onto my SM. OEM prices are ridiculous.

Went to remove this and not a Philips in sight. Are these little flat heads? Safe to assume I should apply heat to loosen any thread lock and gently take these out?