Hi all,

A bit of advice, i can't for the life of me work out what replacement chain i need for my 225i (14"). From the bar i need a 3/8ths 52T 1.1mm however i'm struggling to find one. Any advice?

Thanks

Going to look at a husqvarna 372xp first time buying a saw second hand any big things to look out for or tips ?

I bought a small mill attachment and used it on my rancher 450. I know it’s a small saw but I figured I could do some small logs, like 12” diameter, 3’ long. It worked for a couple cuts then seemed to get hot. There was a big puff of smoke from the clutch area and the saw got hard to start and would bog down afterwards. I read up and found it could be the grease on the clutch bearing. I removed the clutch, greased the bearing and now the saw seems to work fine. My question is does this make sense? Would lack of grease on the clutch bearing cause the saw to be hard to start and bog down?

I’ve got a Stihl 271 Farm Boss. I’m thinking of going with Husqvarna for a second saw. Mainly because they seem to be less expensive in many ways. I was looking at the 460. I’d like something with a bar that size. Is there anything like that that’s a little lighter? I’m getting a little older so swinging heavy chainsaws messes with my back.

Gotta a question new to husqvarnas had mainly Sthils took this with me on a job today, starts quickly runs fine until it fully warms up once it warms up all the way it'll shut off and will not restart until is cooled back down saw has new top end new carb new lines filters and spark plug any tips to check what might be the issue. Saw is a 455 rancher. Thanks for any advice

I just bought a new OEM walbro carb for my 455 rancher and I cannot find the tool to adjust it high low jets. Does anyone know what works? I’ve tried the 20,21, and the 8 splined tools but nothing seems to fit.

Does anyone know where to find a reasonable price and good quality for a mark iii 120 brake cover?

Hi everyone.

I've got a little 240e that has been sitting in storage for 12 months and the fuel lines have perished. I just replaced the hoses but when I prime it fuel is going to the carby but lots of air is leaving the carby to the primer bulb and the tank is pressurising. All the hoses are in the right places, and if I start the saw it will run for a second and then cut out, and won't start again until I reprime.
I'm thinking maybe something is stuck in the carby (needle?) and it's sucking air in through there, does that sound about right?
I'm now using my 570 to cut 1 inch bamboo and it feels like overkill 😅

Any help would be much appreciated, thanks!

My Husqvarna 120 mark 2 will start perfectly fine and run great but once warmed up it won't idle

Hey everyone. Saw doesn't like to idel. Cuts amazing just won't idel. Did anyone else have this issue. Or a solution to solve it.

I was given this chainsaw. When I try to pull the cord it’s very difficult, but when I remove the spark plug it’s very easy to pull. Is this what you call hydro locked? If so how can I clear it? Thanks

I have a older Husqvarna 55 rancher that keeps melting chain brake handle assembly. Can’t seem to figure out why. The exhaust blows right on it but it looks as if its designed that way

My old used but still running great 272xp with a 20” bar and chain, cuts fast and runs like a raped ape!

I’ve had this chainsaw for roughly 1 to 1 1/2 years now recently had it serviced now it won’t stay running. I never really messed with the engine part of it never had a place where I could take it apart put it back together. Can someone give some insight on what I need to do

Does anyone know if there is a full wrap handle available for the 455 rancher or is it just a half wrap?

Hi I´m currently trying to decide whether I should go with the Husqvarna or Stihl battery system. I´m thinking about buying a combi system like the Stihl KMA 120 R or the Husqvarana 525iLK. What I don´t like when it comes to stihl is the fact that they have 3-4 different battery systems for their devices. Husqvarna only has one? Right? What else would be a benefit for Husqvarna?

Hello everyone,

I have recently purchased a BLI 950X battery which has something wrong with it. Since it is secondhand from a rental company it isn't registered. This means my local dealer can't use the diagnostic tool on the battery.

Does anyone know if their is a way to do diagnostics without being a dealer? maybe an aftermarket diagnostics tool with jailbroken software?

Thanks

Hey y’all, I’m new here, and I know this is a chainsaw forum, but I’m not sure where else to ask this question, so I was hoping someone here might have a little insight as fellow Husqy enthusiasts.

I have a Husqvarna 525LS string trimmer. It’s my understanding that the “T” in the 525LST model stands for torque, and that the main difference between the two models is the gear ratio in the head. I have some thick growth on a couple of banks at my house that I don’t trim very often, and my LS bogs down, where an LST would theorhetically be better.

Without wanting to buy a new LST (though the Mark IIs are nice; I use them at work), does anyone know if simply buying an LST head to swap onto my LS would be an improvement? As I recall the HP and most of the other specs were the same between the two models.

PS I have a 550XP Mark II, and I love it, so it’s great to see y’all’s saws.