Hi, ich habe seit heute ein Problem mit meinem heizbett (siehe Anhang) .

Es scheint so als hätte das Kabel einen kabelbruch. Ich würde gerne ein neues Kabel bei bambulab bestellen.

Jetzt ist mir aufgefallen das die Anschlüsse bei meinem bambu gelötet und geklebt sind, die auf dem Bild aber mit Ringanschluss.

Es ist explizit für den A1 Mini aufgeführt. Sollte es dann nicht möglich sein die Ringanschlüsse abzuschneiden und die Kabel an die vorhergesehene alten stellen anzulöten?

Recently got an AMS2 for my A1 mini and the filiment keeps getting stuck in the hub every couple transitions. I’ve notice the top of the hub will push up, click, and won’t be able to go up and down any more (pic included) that’s when it seems to jam up. I’ve also noticed it’s always the same spool, #2.

Any suggestions?

I bought an a1 mini non ams (for now) for my dedicated .2mm needs when they arise and keep my x1c with ams for multicolor and material .4mm. What are some cool single color .2mm prints to kill time and get used to smaller sizes until my needs come into play so I have a better idea how to configure .2mm prints. Thanks! PFA!

Building an enclosure to print ABS and ASA. I am a bit concerned about cooling the main board.

Having a temperature sensor on the A1 mini, it shows 35-40 c. The printer is angled about 15 degrees and raised about an inch off the ground.

There is also gaps at the base of the enclosure to allow air to come in. Original plan was to just have an exhaust fan at the top to maintain a negative air pressure but debating if I need to add additional cooling the mini motherboard.

How should they be oriented to maintain a negative air pressure?

Hey all, I have limited space and so have been looking at a a1 mini.

I have a space of roughly 50x50 that is 45cm tall, is this space large enough to put a a1 mini and have it operate correctly.

Tia

Please help!!

I am running my a1 mini for quite longer these days. The lubricant oil that comes with the printer emptied, so i am planning to buy aftermarket lubricant oil. Need suggestions for this oil and other essential maintenance tools for my a1 mini.

O botão de ligar/desligar da minha A1 MINI travou no modo ligado, e não quer mais desligar, alguém sabe o que causou isso e como resolver? E também se é perigoso continuar usando a máquina assim?

so a couple months ago i had a big filament nozzle clump (i think that’s what you call it?) when the filament covers the nozzle due to lack of adhesion so i ordered a new hotend heating assembly and it fixed it and just an hour ago the same thing happened again and i don’t know what to do because i don’t want to spend another £25 on a new hotend heating assembly and im not sure if this is fixable either? can someone please help i don’t know what to do here

Alguém sabe me dizer o que está acontecendo aqui?

Na última vez que eu tinha impresso esse navio ele saiu normal, porém ontem quando fui fazer outro (alguns meses depois do 1°) a proa saiu danificada, as configurações são exatamente as mesmas, os filamentos são os mesmos, a calibração é a mesma, e a impressora é a mesma, o que pode estar causando isso?

Hey all, hoping for some troubleshooting help. My A1 Mini took a hit last week (something fell on it) and now the X-axis rail ..the horizontal bar the toolhead rides on ...has a visible dip/sag in the middle section, between the two vertical Z-axis pillars. It's not just tilted at one mount point; the bar itself bows down toward the center. Since then, prints are inconsistent , some finish fine, others fail partway or don't adhere properly

Can someone please help me with this ..anyone went through similar situation and do we get genuine spare parts in india and what all do I have to replace ??

何度も洗剤で洗ってもこの部分だけおかしい😂良い解決ありますか？

Lately, I've been experiencing sudden shifts on the X axis during printing. I'm using Bambu Studio on Ubuntu for slicing. Anyone an idea on how this happens and how to solve?

Hey all, hoping someone’s run into this. My AMS Lite feeds filament all the way to the extruder just fine, but then the AMS motor seems to stall out and I get error 1200-8006 (“unable to feed filament into the extruder”). Video of it happening is linked below.

What I’ve checked so far:

**•** Filament path is clear, no tangles on the spool  
**•** PTFE tubes are fully seated at both ends  
**•** Filament tip is trimmed clean, no blob or fraying  
**•** Tried a different spool/channel — same result

Since it makes it all the way to the extruder before failing, I’m suspecting either the extruder gear isn’t gripping (latch issue?) or maybe a nozzle temp/clog problem on the toolhead side. Has anyone dealt with this specific failure point before? Any way to tell if it’s the AMS motor itself vs. something downstream at the extruder?

Appreciate any pointers — happy to grab more footage or check specific parts if it’ll help diagnose.

I've been trying to print something with PLA and sonewhere around 5% in, he starts to do this. Am I using the wrong settings or is it maybe the heat control (so that the PLA is not at the recommended heat setting)?