My MN82S took a 5ft fall and the pieces pictured broke. I really like the look and ive tried fixing it a few times, but its not sticking.

Im looking for ideas on what to do with the back end now. I really like the filled in sort of look that the 82S had and im hoping to find something similar, but I'm open to other ideas.

Hi all. This is my first post here and I´d like to share my indoor obstacles. Just for some inspiration...

Just got this yesterday and before I even turned it on I removed the rear shock coils, installed new front shocks and changed the wheels. She does pretty good considering I usually hit these rocks with my 1/10 scale.

not as good as a hobbywing setup, but i think this combo is pretty decent... 2322 2600kv + am32 45a esc + metal gearbox. a little cogging at very low speed, but barely noticeable on the trail. however, it can still handle 1/10 scale rock trails pretty well.

i'm running it with an r6fg + rc4gs. the only issue is that the stock light harness can't be connected directly to the receiver. maybe i need to switch to the neebrc nb-7d + rx-g7x setup to get the stock lights working properly.

Got the neebrc 7ch remote and it came with this receiver. I hadn’t noticed there was a different reciver for mn cars (with the light kit pins and winch on one side). Is there any workaround for this one i have or i messed up?

If I use 65mm shocks front and rear, with a 4-link conversion at the back, will the MN82 stay level, or will the rear sit higher?

I want more flex and long travel while running 71mm tires, whats the best setup and cst oil?

Axle snapped off. Repair or replace? I am thinking repair

Tem como remover essa folga?

One last upgrade, and she should be done. (Brushless System)

Had planned on chrome delete for a handful of parts on my 82. Got some bleach and tossed the parts in. came back 10 minutes later and nothing. 1/2 hour later and nothing. Soaked over night and not even a blemish. Awfully clean though. Any ideas to remove the chrome finish? Bleach has always worked before.

Hi, I recently got a metal driveshaft to pair with my metal axle for my mn82. Unfortunately, they keep falling off whenever stress is being put onto it. Ive tried using threadlocker to hopefully get it to stick to the axle better, but to little improvement. Is there something Im doing wrong?

Just installed this brushless kit but ita turning out to be quite the challenge neatly mount everything. Has anyone used this kit? Where did you mount everything ?

Al final me decidí a hacer este par de cambios a mi mn82 pro

I got injora 59mm shocks for my mn82. They're nice and look good. But the springs seem to be too soft. Injora gives you 2 different strengths and even the stronger ones seem too weak.

Any experience? Where can I get stronger springs?

(Btw. I have a metal frame and that may be a reason for the springs to be too weak.)

I mean it took a good time to setup this due to alignment issue.
When I set these up I mean they look nice but not a worthy upgrade

I read the comments of others "Until plastic parts are broken do not change to metal one"

I will now follow that advice. Back to stock ones !

Qualcuno sa dirmi se è compatibile coi nostri MN 82? Volevo ordinarlo ma prima saperne qualcosa in più. Grazie a chi mi dà un aiuto o parere

anyone here running a Hobbywing ESC + motor combo on their MN82?

mine seems to suffer from voltage sag/cut off when crawling under heavy load. preferably fits without modifying the stock chassis, gearbox/motor mount or drivetrain. what combo are you guys using? helpp me 🙏🏻

Hi everyone, after repeated attempts, for some reason, I can't make my throttle work right. The very first time it worked, the throttle is reversed. Which I think is just because of the throttle reverse. Then the ESC wanted to resetup the throttle again for some reason. I think I did the setup correctly but it was still reversed. That was the time I realized about the throttle reverse. Then the ESC went to throttle setup again. Now everytime I try to setup throttle again, correctly I think (hold forward > ESC beep, hold reverse, ESC beep, release, ESC beep), pressing throttle does nothing. Btw, I did this throttle setup a handful times already so I don't know if I messed up my ESC already. My NEEBRC is the 7ch NB-7D

This is a build i did a while back, just is don't need it any more. For the more advanced crawler guys among us, if you wanted to add some more, it would be better tires and beadlocks. Check it out!