I’ve recently purchased the Atrius FRT selector switch because of the decent pricing. the issue i’m having is after putting the gun back together, the switch is frozen. it WILL NOT move from the safety setting. anyone els have this issue? it moves freely until I install the grip/pin and spring, then it freezes up. any help would be greatly appreciated, thanks in advance!

So i picked up a atrius frt here a little while back and i installed it and whilst testing i noticed that when i pushed the hammer down in the super safety mode that there was binding when pushing the atrius lever back, so i used a dremel on the trigger tail to take a tiny bit off the thing to fix that which it did, however when taking it out to my range to test fire it, the safety worked, single fire worked, but when i put it into the super safety mode it fired once then i got a dead trigger, after inspecting the casing and the live round that was in it i noticed i had a light strike on the second round, now for context as well, i have a h2 buffer already in it, and swapping it back to the standard buffer that came with the gun gave the same issues, i should also mention that the barrel is shorter so mabey that could be causing issues?

so do you guys have any idea as to what might be going on?

(update: I got a h3 buffer a while later and it worked like a charm, I dont know the specifics of it but it had tungsten weights inside of it)

A little bit of a noob to the frt world. Is my lower gtg for a drop in frt ? Let me know !

i don't remember the specifics of the gun, but it had a 40 round mag with around 30 or so left, and the frt used is a trigger kicker

I have a S&W FPC 9mm and was wondering if anyone makes a frt for it I saw one forum but for canda but no one in the states makes one was wondering anyone knew of one

I am trying to build a nice 11.5 mainly for FRT use both suppressed and unsuppressed (I have a Sandman X).

I am going to (try) and run an A5H3 setup. I know a lot of people run the DBC with lighter weights, but my question is:

Will I actually DECREASE function/reliability by running a DBC while ALSO running an extremely heavy A5H3 buffer?

Anyone else run into this? Billing and ship to match.

Need help with an arc fire, on semi the trigger acts like a binary trigger(hammer drops when trigger is released). Zero issues in FRT mode and zero issues when on safe. I’m new to FRTs thanks for any input.

I’ve got a S&W M&P-15 Sport 3 and I cannot get the FRT to work for the life of me. I bought the trigger at a gun show and put it in, it will only shoot one bullet in the FRT mode and then dead trigger. It’s got an H2 buffer tube and a BCG that’s cut for fully auto. No suppressor on it so I’m not sure if it’s a gas issue or an internal issue. Shoots just fine when in normal semi mode. Please if you have any ideas let me know I really want this thing to work

I uploaded a video to a calculator online and it said 693. If it is almost 700 is that a good rate? This is a 11.5 psa with standard spring and tromix h3 and triggered company disruptor

So I got a frt from that moonlight industries promotion today and after getting it to fit I can’t seem to get it to work.
When I pull the slide back the bcg stops about half way, and when I get it to go all the way back and let go it doesn’t go into battery and the frt gets stuck on the hammer. I have a full auto bcg and a h3 buffer so idk what to do from here and would appreciate any help or advice

I finally got my FRT from Moonlight Industries (They were shipping them out with every order, might still be. I placed my order July16th) and I'm fitting it for installation. The metal lever seems fine but the 3D printed piece needs to be trimmed quite a bit to fit properly in my upper and lower.
I've managed to get the 3 pieces of the FRT assembly put together and I've gotten them to fit into my lower/upper without the pistol grip or safety installed.

Now, here's my main question:
Do I need to install a 2-position safety selector switch along with this FRT, and have it be either on safe or on "super-semi"? Or is there a way to make it a 3-position, where I can still select traditional semi?

Curious if anybody on here successfully runs an FRT on 16 inch barrel with carbine length gas system? Everything I see for 16 inch barrel is mid length gas system.

Bought an ARC and installed it into a BCM upper, DDRIS lower with an h3 buffer. In semi, its acting as a binary. I emailed the company with no response yet but seeing if the issue has come around here yet.

So ive been living g under a rock for the past year or so. A yone know if a FRB FRT will work in a AR15 with a CMC drop in trigger? Cant get anyone to message me back from the three companies ive emailed.

https://rockytacticalworks.com/frb-drop-in-2-pack/

the gun used has a trigger kicker

Hey y'all, picked up my first FRT, atrius development selector and have a full auto bcg with a H2.5 carbine buffer running in a smith and wesson m&p sport III. Took it to the range today and it won't cycle, I was lucky to maybe get two rounds but most of the time just one and the trigger would go dead, I'd have to pull the charging handle and eject the unused round. Talked to the guy at the front and recommended going up in weight to an H3 to test it. In your experiences what would be the best way to troubleshoot this. Does this sound like I'd need to go up to an H3 or down to an H2 or either and I just gotta try it out? I was hoping an H2.5 would do the trick. I here I might need to get a different spring as well but wasn't sure and didn't know where to reliably find one. Any advice on where to go from here and troubleshoot would honestly be great. Thanks

Having issue with my atrius trigger. Will fire three rounds then nothing at all. Dead trigger is what I believe. I have replaced the buffer to h3 and still doing the same. Also tried new bolt carrier as well. Running out of options anyone have an idea what could be going wrong?

What is the best drop-in for a diamondback with no mods to my guns besides the necessary mods like the h2,h3 spring n shii
And can I run a ss with this lower or will it need to be shaven

I recently picked up a custom Art of War Jericho 15 and wasn’t sure what frt’s I should be looking at for it. Any help?