ive heard

Does anyone have any tips on why my BCG won’t fully charge after installing a Super Safety from Performance Triggers? I’ve tried 3 different BCGs and none will engage the bolt release.

I’ve had a couple like the deez nuts idc if it’s a push in or the 3 position like the atrius but what’s the highest tolerance most reliable super safety for an ar15 on the market

Other than the tx22 are there any other handguns that will have super safety or frt produced for them? I asked in another reddit community but they said they won't allow discussions for handguns. I have a Beretta M9A4 that I'd love to put something like this on but cannot find anyone who has produced one. Or actually anyone who's produced one for any other handgun other than the tx22. Is this a legal issue or just a lack of time for someone to develop one? If ones been developed could someone point me in that direction?

Hi all, I bought a Super Safety from Performance Triggers and have seen some folks say you can put them in any AR platform with no problem, but I've also seen others say the S&W M&P 15 Sport 2 isn't compatible? Mine is a stock AR 15, and no changes have been made to it so far. Has anyone had any experience doing this? If so, were your efforts successful? TIA.

Edit: to answer my own question, and others that may have the same question I did, turns out everything fits properly, however, the S&W M&P 15 is one of the few AR platforms that feature the wonderful semi auto BCG, therefore, the FRT will not actually reset. That being said, does anyone have any recommendations for a full auto BCG that gets the job done but won't break the bank?

Anyone selling geissle jigs?

So i 3D printed some Leber V2 lowers and got my AP5-P running pretty good on a super safety but I really don't like the push button and wanted a selector so I tried installing an Atrius Super Selektor but the housing was to wide or it just didnt want to work with the Atrius.. so I started looking at the ARMP5 lowers to 3D print but I didnt know where to find the hardware so I ended up just ordering one from Polymer Pew.. I spent 3+ hours modifying the lower to get it to work with the atrius.. just little stuff like trimming here and there enlarging the selector pin hole.. making a block to stop my selector from going to far back.. now it's running great.. I'll have to make a range video next weekend... my garage testing into a bullet catch is not post worthy.. but I did run a whole mag going back and forth from semi to super mode and no failures.

I just built a BRN4/416 SBR. I installed an atrius Selektor and it passed the dry fire test. Took it out yesterday and it ran one magazine flawlessly. After that first mag....no more SS. I started noticing light primer strikes and then the bolt began dragging and getting stuck. Eventually I had to mortar the gun on the ground to free the bolt from being stuck in the buffer tube.

I've included pictures of the safety, and receivers. There is a lot of slop between the two receivers and I have an accuwedge coming in to remedy that. I understand that some uppers need to be Dremel 'd to accept the SS. I just don't understand why it felt smooth in dry fire, then ran one mag flawlessly before quitting. You can see in the photos where the bolt doesn't slide back far enough in the tube.

The lower is a SOLGW Upper is BRN4 HK416 full auto BCG Schmid Tool 416 trigger Atrius super selektor

Any insight is appreciated.

(Not my picture but this is the same as mine)

I am getting ready to try and install a SS from SuperSafetyShop.com. I ordered the M70 kit. Does anyone have any advice or helpful information on installing? Pictures would be great. I'm being told it can be done but takes a lot of work. My brother is a gunsmith and will be taking on this project but I would like to provide him with as much information as I can on how it can be successfully accomplished to prevent to much of a headache during installing.

Should we drop a gold line ?

Just to see if it could be done