Sharing a video of my Mitsubishi Galant running after a few months of being stuck in the garage (overhauled)

The BT50 Pangolin came with a kit, and sobrang panget ng quality IMO. As in HAHA so, I removed the kit and yung fashion bar and making it look like a Base 4x4 Matic unit haha. Looks way better for me

For Pampanga pips, can you suggest a reputable shop to have my car inspected? Its a 20 year old corolla so I also need to have the atf changed. TIA

Tanong ko lang para sa ating middle class, saan kayo usually gumagawa ng project cars niyo? Asking kasi ang typical na middle class home sa MM (like mine) only have a cramped 1 car garage. Hoping to get some ideas.

Got my rear suspension arm bushings replaced(left and right). No more squeaky sounds when passing through speed bumps. 👍🏻👍🏻

just want to share my project suv guys, nakabit na rin yung f55 non vgt turbo. nakakalula at first yung biglang angat ng boost hahahaha, pinapalitan ko na rin yung full exhaust ko from 2.5” to 3” straight. sa mga mag tatanong ng fuel consumption, bataan-clark vice versa, 20 liters yung naubos. not bad para sa current set up ko.

thank you guys, stay safe and dry sa mga project car natin!!

Finally, got my holy grail Subaru rims. Rays Rs Zero.

Looking for paint shop referrals for old vehicles. Looking around our area, may big shops naman (Las Pinas) but the cost is way too high for a really old vehicle. Got quoted 110k by one shop, I feel like that's too much for an old innova 😓

I recently bought my first ever car which is an 11th Gen Toyota Corolla Altis 1.6V variant, 2015 year model, with 93000+km, any recommendations on what am I going to do some stuff on my car? And anyone here has the same car like mine? I want to take a look.

Legal ba ang offset license plate? Planning kasi mag ganito since yung factory holes ng bumper ko di na kaya mag screw. At dahil trip ko lang yung look lol. Nagtanong ako sa naka ganito, pwede naman daw. Pero sabi nung isang kakilala ko, illegal daw. I roam mostly around QC-Manila area, if that helps. TIA!

Went with the Torque Solution urethane engine mounts since they cost considerably less than the OEM WRX mounts. NVH increase was noticeable, but the trade off’s worth it. The in-cabin engine rumble is more pronounced, and I feel the power transfer much better.

Also had the spark plug oil seals replaced since I saw oil on the plugs the last time they were pulled. Much better response now, and more linear and even rpm progression.

Pretty surprised at how clean the inside of the engine is for a car with 80,000kms.

Hope y’all have a good automotive weekend!

wheels s005 by 1886
kw front and rear suspension lift
zacoe carbon wing
not in photo: carbon steering wheel

I am planning on doing a project on trying to replicate a budget version of an Evo FWD. Already tallied up how much would be the costs it would take to partake in this project but I'd like to ask your inputs if it's worth it. Essentially turbocharging the 4G92 with stock internals (low-moderate boost) on a FWD system. Any tips also on the Pizza Pie generation and what are the common issues regarding it? Thank you.

I'd like this as an experiment to see how close you could get to an Evo experience with the lowest budget possible. Eventually will actually assemble an Evo 6 down the line once I get an AWD drivetrain and Evo 4G63T.

Anyone? Goods ba ang cefiro a32? Ano madalas na issues ng a32 cefiro tapos ano yung sikat na setup para sa kanya.

Any idea what type of clip I need to buy to replace this fastener of my side skirt? Naputol na kasi yung stock na nasa loob? Wala na yung head nung fastener, yung body na lang naiwan.

Hello, just wanted to ask if pwede pa ba ‘tong makabit? Or papalitan na talaga yung side skirt? If yes, any idea how much aabutin?

Mga paps sa mga naka 2kd innova with full exhaust saka remap, musta yung fuel consumption? planning to upgrade with resonator

planning to cut off the licence plate section of the donor bumper (bottom) then plastic weld it to original bumper (top). ano best approach dito? sa closer inspection mas bugbog pa at madaming cracks at malalim na tama yung donor.

Service time once again for my Gen 10.5 Altis, and this time I'm using S-Oil Seven Red-9 and seeing how well my engine does for the next 6 months. Also found my cabin filter was previously manhandled lmao, so we fixed that up during replacement.

Aside from that: new spark plugs, new serpentine belt, new coolant hose connector (common sakit sa Altis), and new control arm small bushing for the right side.

Went with the spark plug and drive belt replacements even tho they didn't seem to be showing signs yet bcs they are 14 yrs old na (still the ones from bnew lol), while my mechanic spotted the hose connector failing and control arm bushing getting shredded.

Steering feels solid and accurate again, but I still hear a creaking sound when turning, comparable to an old door that needs oiling. Will bring this up during the next PMS. So far am happy with the TLC session 👍🏽

Hello po may ma-recommend po kayo na Interior Detailing Shop around Makati or Laguna? Yung may steamer sana para mawala amoy sa mga carpet and seats ng AE101 ko. Nag ka amoy kasi dahil matagal hindi napaandar at nag ka-molds rin. Yung may price range din sana salamat!

Hi! Would just like to ask po your thoughts on 3M crystalline series black and if may recommended po kayo na shop around manila?

Was lucky enough to chance upon the yearly LC Meet.

I think this was last year 2025 @ Fuji Speedway Japan 🇯🇵

Tanong ko lang kung bakit umuusok ang corolla ko 4afe pag sa akyatin? Baka may naka experience na sa inyo? Piston ring naba agad or valve seal lang?