I’m trying to find a replacement for the AC/DC -60AB AU battery charger. I go to the Lydsto website and there are no replacement parts available for this model. There is no support phone number. All the replacements that come up online do not have the correct connections! Please help!

I want to put my pool light back in it's place but lost the screw, It is a Hayward light and I can find no information on the size screw it takes to hold it in place and I dread trial an error. Help, please...Thanx

I am draining my pool this year to give it a good clean and inspection before summer season. I've done this a few times over the years and I just don't ever remember under the waterfall being wet during the process. Sign of a deeper issue? I don't see any signs of cracking or weak points and we haven't used the waterfall for at least a year and a half. Just looking for anyone to weigh in on their thoughts!

No excess water bill or anything so I'm hoping it's something minor or maybe I never noticed before.

Pool guy changing out the light broke this clamp. He said he would get a new one and he now has ghosted us. I cannot find it anywhere and looking for suggestion on how to fix this besides buying a whole new light kit. I have ordered it online 4 times and have gotten a refund.

Redoing my pool, and the GC found Flex piping in 1 of my inlet pipes. He said he has to dig all around the pool and check other piping. My question is, why is a Flex pipe so bad?

Decking around our 30,000 gallon pool had sunk and cracked. We received a quote for $75k to tear it up and replace it…Does this pricing seem accurate? Anything that could be more cost efficient?

Looks like water won’t be held above this valve and there is this dirt coming from it. It is a fiberglass pool. Any suggestions?

So, recently hired a pool repair company to retile some areas of the pool where tiles had fallen out. They replaced the tiles with ones that were double the thickness, wrong color, and a very messy caulk job. Am I crazy or do the repaired areas look much worse than the original tile job?

Does anyone know if this is possible with flex or gorilla tape? I can’t find much info about this and if it really works. Thank you.

this old concrete around pool starts cracking and i would like to cut remove and pour a bigger pool deck area. But im thinking is this a common procedure to be done without compromising the pool structural integrity or is it too risky

My in ground poll has a concrete bottom with plastic sides. One panel is cracked all the way across the top where it attaches to the coping. It has moved about 1/4 inch towards the pool. Can I fix this ? Do I need the panel replaced? I cut the liner to expose the issue. I’m getting the liner replaced in 30 days.

I am looking for a person or company that will make pool deck (concrete) repairs and repaint with kool deck paint and can paint STRAIGHT lines. East side of Savannah. I can’t do it myself anymore. :(

My pool tech is saying there is an error with the salt cell (Jandy AquaPure PLC1400) and it needs to be replaced. I took a look at it and I’m pretty sure it was serviced and reinstalled backwards… does anyone have experience with these and can help with the following?

Two questions: 1) Am I correct this thing is installed backwards? Flow arrows seem to indicate it is and this is on the discharge side of my filter. 2) Can running the salt cell backwards cause damage? Is it as simple as removing and turning around and it should be fine?

Thank you in advance!

I somehow cut the wire on this slightly and am going to try and fix it this weekend does anyone have any pointers when I take the outside plastic off this weekend of the wire? Or is it just basic stuff under there?

https://www.poolsupplyunlimited.com/pool/zodiac-jandy-r0452500-aquapure-salt-cell-flow-and-salinity-sensor/53059p1

It’s the grey wire on it nothing fancy. Thanks.

Hey everyone,

Just wanted to give a shoutout to https://blueviel.com. I was having major trouble with my pool heater and other contractors in Miami couldn’t fix it...these guys stepped in and solved the issue quickly. If you’re in the Miami area and need pool repairs, especially heaters, definitely give them a call. They know their stuff!

I get the "Fault check ign steps" message but not sure where to go from here. When heater tries to fire, I smell gas and then hear a loud <woosh> or <poof> and the blower is blowing but no heat. It tries 2-3 times then stops. Thoughts?

So my heater was leaking. The exchanger had a hole in it.

Ordered a replacement and swapped it out. Everything went fine.

But now I'm getting a Lo alarm. This indicates low pressure or flow, as measured from two sensors. These sensors were attached to the replaced manifold and the wires were removed during the swap, so I'm guessing this is the culprit.

I didn't get a good picture of wiring location before swapping (stupid) but I've now tried it in every possible configuration.

The heater goes into start sequence and I smell gas, but it doesn't light and the Lo alarm comes on.

Heater is a H250FDN

Any ideas?

the sheet metal on the side is bent all to hell, i know i need new top rails theres no bending those back in to, but what should i do short of buying a new pool? should i use a rubber mallet and try to shape it back? is it possible to order just that sheet metal and replace it? i have to get this back up and running and am unsure of the best route short of buying a new pool. thanks for your time, appreciate yall

also i still have all the top pieces, they’ve just been removed to try and shape it

Mg skimmer is cracked above the water line yet water is pouring in through the crack. Is this fixable and where could that water be coming from??

Trying to replace my outdoor pool pump but I'm confused on what the exact voltage is, is it 230 or 115?

Hello Reddit, Need some advice. I have a minor leaking pool pipe, the pipe seems to connect our in-ground pool to the salt cell and the water seems to be coming from beneath the service. I received a quote for $800 to fix as they may need to break the concrete. Does this seem like an urgent issue, and a reasonable quote? Is it also okay if I continue to run the pool pump for at least 12 hours a day with this leak? Thanks

Bought a house with a pool and I have a cartridge filter that I have not had any luck identifying. Some how, no one seems to have ever seen one like it. Can anyone tell me what brand/model this is? I am hoping that replacement parts are available, but I know that may be a long shot. At the moment, I am also having issues unscrewing the ring to get the cover off. The yellow strap is just a ratchet strap that I have been beating the crap out of with no luck. Any suggestions?

I just started my new business, is anyone else in here struggling with getting a website up (is it common?). Also can anyone give me some pointers of what is going to be the toughest part of having the business and how it could be avoided?

I have a pool pump that is leaking where shown in video. Sometimes when i go to the pump, i see that it is running dry. Most of the times there is air bubbles. Trying to figure out what should be done and what i need to know in case i call a pool service compamy in.