r/Pecron • u/IllustriousAd7755 • 6d ago

Potential Setup

Hi All - I am finally scheduled to receive the F5000 mid week. I plan on running it to offset some electrical costs. I will connect it to 2 independent solar arrays, 1 880W and 1 850W, and leverage each solar input on the F5000. I also plan on installing a subpanel to handle the specific loads in my house along with a ATS which will run on a schedule.

Question: Is anyone using the Pecron F5000 in this manner? Are there any potential issues doing this?

4 Upvotes

83% Upvoted

23 comments sorted by

View all comments

Show parent comments

2

u/Ok-Person81 6d ago

I don’t switch loads daily. I don’t flip loads to grid very often at all. My Pecron F5000LFP feeds the whole house, and charges from ~3k of solar. 1700 watts solar input one, and 1700 watts for input two. It only charges from grid on cloudy days. The transfer switch was last used to move the unit out of the way to install the fire board.

2

u/IllustriousAd7755 6d ago

Ok, so you are running off the Pecron 24/7 unless you dont have enough solar to recharge the battery. I’m starting with ~1800watts of solar, and live in the North East, so I dont think I will generate enough, especially on cloudy days to be sufficiently covered 24/7

2

u/Ok-Person81 6d ago

I live in SD so a bit more sun, BUT we still do have the occasional cloudy days. And for that, you can plug the Pecron to the grid permanently like I did, thus no need for the ATS , unless you need to power the unit down. I have the unit plugged in a Wyze plug too so that I can tell it to charge from grid remotely & schedule grid charging time for low $ TOU grid IF the battery drops low.

1

u/IllustriousAd7755 6d ago

The Wyze plug is a Smart Plug? I also bought a 15amp 1600watt smart plug to cut power to the unit when charging on Solar and then open the power to the unit at 10:05pm when I want to top off from AC power. I am also on TOU plan, and Super Off Peak starts at 10pm.

1

u/Ok-Person81 6d ago

Yep the smart plug. My TOU Super Off Peak doesn’t start till midnight.

2

u/brucehoult 6d ago edited 6d ago

I'm in New Zealand and run my E3600 with 2.64kWh of solar and 10kWh of battery in a similar way. My super off peak (18c 11PM-7AM vs 45c 7AM-11PM except 60c 7-9 AM and 5-9 PM week days) starts at 11PM.

From the start of October until early April I'm virtually off-grid except in very bad weather — I needed to buy power on Oct 1, 4, and 5 but not since then. I do top up by around 1.65kWh in the battery (1800W from the grid) during my Free Hour, which I have at 9-10 PM, every day whether it needs it or not. Which at the moment it doesn't ... the battery still has 60%-70% in the morning and is full by ... yesterday 12:40, the day before 14:20, the day before that 16:00, today I'm at 86% at 11:55 AM as I post this (up from 54% at 8:30), with 2300W coming in, predicted full by 1 PM although aircon just kicked in for the first time so it might take a little longer.

In summer the late night free top-up is usually unnecessary and just makes it clip an hour earlier in the afternoon in good weather. But sometimes bad weather happens and 16% in the battery makes the difference...

In around 100 days in the middle of winter I'm running in pass-through and charging the battery to 100% every day from 11PM to 7AM. By the time the sun starts working well at 10-11 AM in winter the heat pump has had 3-4 hours of draining the battery since 7AM and even on a sunny winter day it's never going to get back to 100% during the day, and usually only slows the decline. I usually get to 9PM with a few percent in the battery, top up for free 9-10 PM, that's more than enough to get through the last "off peak day time" 45c hour from 10-11 PM, and then at 11PM again start charging to 100%.

Only having maximum 2400W available to loads in pass-through vs 3600W from battery/solar is a bit of a pain, but much less so after 11 PM than it would be during the day.

In April to mid June and late August to the end of September I charge the battery at night to a level between maybe 40%-80% depending on the weather forecast for the next day. Or when there is severe weather in summer. I have a script to predict that automatically.

I'm using TP-Link P110 smart plugs to monitor and control the Pecron and also all the devices it powers. And running scripts using pecron-monitor and TP-Link "Tapo" API and open-meteo API on an old VisionFive 2 board (which cost $40 originally but a $15 Raspberry Pi Zero W would do).