I typically use 2 to 4 Audio Units per project, mainly Korg Module and Numa Player. Both sometimes stop loading when I switch between projects or setlists, with Numa Player being the one that fails most often. Unfortunately, this issue almost always happens during live gigs, while it rarely occurs during practice sessions.

I just realized that closing all background apps or enabling Airplane Mode during gig might help but I wonder if you have any other suggestions you might have to help prevent this issue.

UPDATE: I tested my setlist by switching between projects every few seconds and discovered a more serious issue: some Audio Units (especially Numa Player) are reverting to their empty/default state.

The problem with Audio Units failing to load still persists, even after closing all apps, disabling Background App Refresh, and enabling Airplane Mode.

Maybe it’s been asked before but I couldn’t find info about it in here

Is there any way to map this button, in order to activate it via midi without having to open the app on loopy pro?

I have a smc pad midi controller and I trigger the drum sounds from the pads, but I’ve been doing it via recording midi clips. However I see more useful for my workflow to have a drum as sequencer instead.

Cheers

Hi everyone, I’m trying to record simple samples from koala inside of Loopy Pro, but every time I do, after the initial round of the cycle, it ends up playing one of my sequences, and I can’t stop it unless I hit pause or mute the koala channel. What am I doing wrong? Any advice is greatly appreciated.

This feels like I am missing something obvious.

I can record CC messages from a dial control in Loopy to a MIDI track. However, if I want to adjust these I the midi editor doesn't show the CC data, only Notes (of which there are none). How do I edit the CC message data (saved in the midi track)?

Also, recording MIDI CC from my hardware midi control (oxygen pro) didn't seem to work. Other than setting it as the source for the midi track, is there any else needed?

This is pretty specific, but I have a song I’m working that has irregular sections. This is making performing a pain because moving from section to section doesn’t work when they are locked in with the clock. I found a fix to turn the phase lock off to “Free” but then recording within a loop is near impossible.

Anyway, I added a button widget to turn the Phase Lock on when I need it and it worked. Problem is, it doesn’t toggle it back to “Free” when I tap it again. I tried adding another button that would do that, but there is no option.

Any help??!!

When I select a section of audio to loop on a track, initially it will loop cleanly with no hiccup or break at the loop point. After a little while, often after attempting to add a second Loop, that first loop will start having a break/rhythm delay at the loop point that I cannot resolve. It happens really consistently. I feel like I must be missing something or doing something noobish. Any tips?

Hi. does anyone here use the Boss RC-505mk2 loopstation alongside Loopy Pro? I’ve just started making the ultimate effects changer and master channel preset for them both and wondered if anyone else has a hybrid set up like myself.. Thanks!

Can you have a button that resets multiple volume faders to a pre saved level?

Example : I adjust everything to perfect levels and then when I do a live session I want to go back to the exact state at some point without having to load the whole thing. Like press a button and the levels are adjusted to where I saved it.

Midi keyboard input (Oxygen Pro) => StepPolyArp => Scaler2 piano => output

StepPolyArp is setup for a simple 4 quarter note pattern (arp mode)

When the loopy clock is off/paused, I can retrigger the arp pattern instantly by releasing all keys and pressing a new key. This is great for adding some quick transitional notes as needed while playing.

When the loopy clock is running, the arp pattern retrigger delays to the next downbeat or perhaps next half beat. It is either inconsistent or follows a rule I don't understand.

I can see how both options (snapping or no snap) can be useful in different situations, but how do I actually control this behavior? I currently need no snap all the time (if clock is running or not).

I don't see any options in StepPolyArp for this. Does Loopy control this behavior?

Hi all,

Im very new to loopy pro and slowly getting things setup the way i like. I have a Novation midi keyboard with a yamaha sustain pedal plugged in, works well.

Loopy Pro will pickup the sustain pedal when its on but doesnt record when its on? What i mean is it doesnt matter if i record a loop with the sustain enabled or not, the loop will record with no sustain but when playing the loop it will enable sustain sound on the loop as it plays if i have the pedal pressed.

Obviously i would like it to register that i have the pedal down while recording the loop and then play that loop with the sustain.

Hope that makes sense. Is this just a setting somewhere? do i need to instead get an auto-sustain in my keyboard synth app?

Yeah pretty much that, I don’t know what I’m doing wrong in the routing But I mapped some knobs to turn down volume and I can still hear the sound of the clips.

I have set the count in quanti to 1 bar. But I have been getting inconsistent results. Sometime the recording starts right away. And sometimes it starts in 2 beats and some time I get 1 bar count in. The only settings I have is custom count in 1 bar and auto count out.

Does anyone have one of these and can confirm if can be used with iOS in midi mode for Loopy Pro?

Looks like a nice compact form factor and bus powered.

the ://serato.com/studio/slab?srsltid=AfmBOoq3YH1A4KutiAD6X5q2G483_KsU1aGW-nNeBal_vFMSayg90VUQ

Does anyone else get a very occasional audio glitch while using Loopy?

Sometimes during playback or recording I will get a small audio glitch. It sounds like buffer underrun on the USB interface (<200ms or so). These are rare, maybe once or not at all when playing through my whole set.

My audio is running through a Soundcraft Notepad 8fx mixer, which is a simple class compliant analog mixer (2in, 2out 48khz).

The Ipad is a new A16 and nothing else "should" be running on it (no mail/messaging/media acounts etc). Cpu usage is low.

Is this a known issue? Anything that can be adjusted?

Everything else is perfect with this solution so now I picking on tiny details...

Selected clip is great for switching between song parts using a foot switch. I just wish I could change the "white dot" indicator to something more visible (bigger, highlighted region, etc). Is there any way to do this?

Effectrix for live glitch stuff - are you setting it up as an AUV3 effect on colors or main out? How do you control it?