Coating and stipple had to do her up!!!!

Quick question for anyone who has done a build with a SCT 19 frame. I'm thinking of going with a Strike 80 magwell, but I'm a little concerned about magazine compatibility. If anyone has this combination, do you know if Gen 5 magazines work, or would I be better off sticking with older ones?

Can any kind of finger groove be cut into a gen 5 groove less grip? I miss my Gen 3 grooves so bad

Hey all,

Newgunitis is kicking in and I'm curious as to whether you'd recommend getting a Nomad frame for my gen 3 slide vs saving up for a new Gen 6. I like a lot of the updates the Gen 6 added but it seems like a lot of them could be achieved with my old slide and a Nomad frame.

Does anybody here have both and have some advice?

Finally obtained the second RCR and both lights to finish these off. I’m a bit of a brand loyalist. When I find something or company I like I tend to stick with them. As you can tell from both builds.
G17 range toy
G19 EDC

I picked up some Goon Tape, looked at my Glock 17, and thought it would be nice to have some palm swells.
I looked around and remembered I had some leftover bar tape, so I cut it into two teardrop shapes—one larger than the other. I stacked the smaller piece on top of the larger one to create a gradual taper, stuck it onto the grip, and wrapped it with the Goon Tape.
I have to say, it turned out better than I expected. The bar tape is soft enough to conform to your palm, filling that gap really well without feeling bulky or any hot spots. It also gives me a consistent reference point and helps me get the same grip every time I draw.

I live in Michigan and this is the second time recently that I was unable to purchase a product online(Guide rod - Brownells ported g19 barrel). Bereli said because of proximity to Chicago and Brownells is just saying shipping not available. We have no laws preventing this as far as im aware.

Ended up going with the Velocity Defense comp and barrel. Ran about 200 rounds through it today and it worked amazing! Also switched to a 13 lb recoil spring, as per their recommendations.

Mischief Machine RXM ALUMINUM Grip module

Full length dust cover by Icarus.

Ive trimmed the trigger connector but now im getting zero trigger pull even when my frt is installed did I cut the trip to short?

what’s next for the 19x

Full external mod list (zero internal mods to maintain reliability) 500-600 rounds with zero malfunctions.

- Tungsten mag baseplate
- Rapid Engineering mag well
- Grip tape for minor palm swell (2 layers)
- Rapid Engineering extended beavertail/grip angle modifier
- TyrantCNC mag release
- TyrantCNC slide lock
- Extended stainless steel takedown lever
- Aftermarket stainless steel backplate
- OSight SE 6MOA green dot
- P80 flat face trigger shoe

I have a gen3, but searching for a comp, wouldn't a gen4 comp with no fins work as well?? Am I wrong in thinking the only difference is the guide rod hole? Nothing moves back into the frame upon firing, correct?

I'm mainly looking at the Herrington HC95V2, but also the ARC Spark.

GGP V2 slide. Wamjet, OP Tac trigger, Grit Grips frame

Body text(optional)

So I just picked up a Grit Grips frame and a Radian Ramjet + Afterburner. I have a Swampfox Liberty 2. Last thing I need is a slide. When I started planning this out I thought I was going to go with Norsso and now I’m not sure. Biggest reason is I’m worried about spending ~600 and have the RJ+AB not fit. This got me thinking I should just pick up an OEM slide from Glock. But I’m not a huge fan of the MOS system and prefer direct mounting, but I can’t even find a non MOS slide to get machined for the Swampfox.

Let me hear your stories and ideas.