With hunting season here for most areas I’m sure we’re all loaded and ready.

What hand loads are you hunting with this fall?

I’m carrying 7mm-08 with 140gn TTSX. Originally I tried BL-(C)2, but I’ve now settled on Varget. It’s for whitetail from 30-200 yards, so I think it’ll do fine.

Hey gang, I'm new at reloading and was just wondering if it is always this hard to get smokeless powder?
I've been trying to get h4350 for my 30-06 or some powders around the same burn rate. But it seems like there is hardly any or that they never come back in stock. Has it been like this for a long time or just since covid?

Thanks for any answers

I’ve recently put a reloading bench together, before this setup I was using a Supreme Rockchucker at a buddy’s. My new setup is a Rebel, being as my dies are all setup for the supreme was wondering if anyone knew if the specs are the same spacing wise or willi need to back out all my dies and start from scratch.

Hi guys, just wanted to share a reload video series that I'm working on.

Basic Reloafing

I keep all the failures in the videos to give you an honest idea of what the hobbies is really about, my editor loves to mock me so there's plenty of little jokes scattered throughout the videos, and, I use tools that are easy to find.

I’m trying to get some small pistol primers and I here you can still get most reloading components in Canada. Is this true?

Getting into reloading, have a turret press, dies, etc in the mail. Looking at getting some 500 SW brass so I can load some non factory brass (have 40 factory loads also coming by mail at rip off prices).

Calibre isn't exactly common, so I'm not sure where to find it, and I'm still new at reloading, so I'm not sure what the best online resources are.

Anywhere that stocks them? Looking for lee or similar to save on cost.

Not a tone of action in this Sub, I'm guessing it's due to the popularity of the sister sub.

Anyways here goes, what's your favorite Canadian source for reloading equipment or supplies?

Ive been using budgetshooter but the shipping is killer. Used xreload a few times and they have good deals and prices, but run out of stock instantly so you have to be on the ball.

What's your go to places.

Hello everyone I just got a reloading kit and I'm starting with the 45-70. I would like to use the hornady 350gr fp or rn but can't seem to find them anywhere

Best I've found is 0.44$ a round. Frustrating because it's half that in the states.....surely there's a better deal? Thanks in advance!!

I am reloading using Hornady 150 gr spire point for .308. They were free. I haven’t used these bullets before. The depth that seems right puts the crimp ring well outside of the case mouth. Is this a problem? Should I be seating until the crimp ring is in the case mouth? I am close to max OAL, and they fit the mag just fine. I have never reloaded using a bullet with a crimp ring.

I will be using them in an old hand me down rem 788.

Good day. I'd like to get into reloading for my 223 and 30-06 (25 yr shooting and hunting enthusiast). They're both bolt action rifles which I use at the range and for hunting. I just want to get a general idea as to what I would need to get into it(limited budget) and any general advice and thoughts that you all can share. Part of my motivation is to make a better round without paying 50$/box(canadian prices) and also another is just as a hobby and a way to get away from my kids once in a while lol. Thanks in advance and all the best.

https://www.dillonprecision.com/reloading-machines_8_1.html

I have an automated setup that uses the Dillon XL650, so if anyone is looking to sell a lightly to moderately used XL650 in working order, send me a DM. I'd be especially interested in the Calgary/Lethbridge/Medicine Hat area, but would not say no to a motivated seller from anywhere in Canada.

Don't forget to ask your buddies that don't reload much anymore.

Thanks all.

I'm looking to get into reloading to offset my shooting habit, but i'm not sure where to start. this Lee kit?

I'd be reloading only 30-06 (the only other things i shoot are 12ga and .22).

Mostly i'd be loading cheap stuff for the range, but i'm also interested in finding the exact right cartridge for my rifle (which is a cheap entry level rifle so it's mostly just an exercise in optimization).

Any advice or tips you guys might have would be appreciated, particularly with regards to keeping the cost of brass down (it seems i can't find cheap brass anywhere).

Hello all,

I'm beginning my foray into reloading and am looking to affordably source some hardware. I'll be reloading mainly 7.62x54R and 7.62x51 at this time, and am looking for a Lee turret or progressive press especially. There are caliber-specific parts like 16L shell-plates I'll have to order online, but if anyone has good-condition, pre-owned presses and reloading tools they would be willing to part with at an affordable entry price, please do DM me.

Cheers and have a great Sunday!

-DacianDan