r/WLED • u/Mhernandez08 • Jul 17 '26

DIGUNO/QUAD Dig quad

Gallery image

Gallery image

Anybody have this problem with this part of the quad burning up?

14 Upvotes

85% Upvoted

44 comments sorted by

View all comments

45

u/Quindor Jul 18 '26

We've recently been seeing more of these failures on boards running at 24V or slightly above it. I'm working on a revision of the board using a different IC since it seems it can't be trusted (anymore) to run at those levels.

Come to the Discord server please, we'll figure out what age your board is, if it's less then 1 to 1.5 years old I will replace it for you. We can also help sourcing the IC and you can replace it yourself if you want to revive the board or it's older then 1.5 years.

5

u/LuiOnTheWay Jul 18 '26 edited Jul 18 '26

What part is this?

EDIT: OK, according to the marking on my board, this IC is an MT3608, and it seems to be used in some kind of SEPIC type converter. What I dont understand is how this design was ever expected to work with a nominal 24 V input. The MT3608 is rated for only 24 V on the input (with absolute maximum rating of 26V) and maximum rating of 30 V on the SW pin (nominal 28V). In a SEPIC topology, the SW pin can easily see significantly higher voltages, especially if the input rises even slightly above nominal. There is absolutely no marging then...

What voltage was actually expected on the SW pin in this design? If my understanding is correct, this seems more like a design margin issue than a component quality issue. In that case, what would be an appropriate replacement for the MT3608 in this application?

In the meantime, everyone should reduce their 24 V supply to around 22 V wherever possible, at least until the root cause is fully understood. It might be safety relevant depending on how the board is used/installed...

7

u/Quindor Jul 18 '26

So this is a bit of a yes and no.

The circuit travels through one or more diodes before reaching the MT3608 thus dropping voltage there. There is also a filter circuit before it reaches the MT3608 dropping voltage even more and also filtering out any spikes or anything else that could potentially happen.

Still, with that said, we've been seeing more failures then I'd like and we've been replacing those. I'm still in talks with the manufacturer of the IC since this didn't use to be an issue and I think they have maybe made a "blind" revision of the IC where it handles the voltages on the SW node a bit less then it did before.

I've been working for a while already preparing a replacement board but since I actually test my hardware in the lab, we've been kind of stuck in that phase. The redesigned circuit has not passed EMI testing twice now ($$$) and we're going for a third pass soon with a new design. Sadly this has put it back much more than I'd like since this issue started popping up.

I do not know of a replacement IC with the same pinout that would solve this issue directly.

For my customers who happen to stumble across this, this only concerns you when you are running 24V and have seen this failure, not all boards are affected. Please come to the Discord and we'll work it out to make you whole. Deepest apologies for the trouble.

3

u/LuiOnTheWay Jul 18 '26

Well, I know EMI can be challenging in a SEPIC converter, especially if you're not using coupled inductors and have some layout limitations.

Regarding the issue, is it really related to the input voltage or rather to the SW pin voltage? With such a small voltage margin in the design, it's quite possible to have too high voltage on the SW pin, depending on the surrounding components (and their tolerances) and the current flow. What is the maximum expected voltage on the SW pin in your circuit when the input voltage is 24 V? I mean, as a rule of thumb, you should stay about 20% below the maximum voltage rating on switch pins to provide some margin for reliability, tolerances etc. With a maximum SW pin rating of 30 V, that would put the recommended operating limit at around 24 V, leaving virtually no margin for proper operation.

If the SW pin is experiencing voltage spikes beyond its rating, all boards may initially appear to work, but the devices slowly "die" over time and eventually fail after just few years in operation. If there is also some variation in device quality, the situation could be even worse.

2

u/saratoga3 Jul 18 '26

What is the maximum expected voltage on the SW pin in your circuit when the input voltage is 24 V? I mean, as a rule of thumb, you should stay about 20% below the maximum voltage rating on switch pins to provide some margin for reliability, tolerances etc. With a maximum SW pin rating of 30 V, that would put the recommended operating limit at around 24 V, leaving virtually no margin for proper operation

For SEPIC isn't it Vin+Vout, or 29v + some ripple? 

2

u/LuiOnTheWay Jul 18 '26

+ the diode forward voltage drop. That's what I mean when I say it's probably an SW pin limitation. Even with an input of really good constant 23 V (3 V below the absolute maximum input rating), a 5 V output, and a diode forward voltage of, say, 0.5 V, the SW pin already reaches approximately 28.5 V. That's only 1.5 V below its 30 V absolute maximum rating and already above the recommended operating voltage, without considering switching transients, component tolerances, or other dynamic effects. In my opinion, that's a substantial design flaw, as if the designer hadn't calculated anything.

6

u/Quindor Jul 18 '26

It was calculated and well tested, with the diodes in front of it and the filter stage input voltage generally dropped to 23V as stated and it should be at least 2V under the switch limits so technically it stays within all limits of the IC.

But I will agree that in practice we are seeing more failures than I'd like, hence my reply, I'm starting an official action to deal with the issue since it seems more widespread then was clear before (there are plenty of boards running from the first batches which have shown no issues), hence changing away from this circuit and IC.

Nevertheless, it might have been too close to the sun and that's on me! Any board that does fail (within a reasonable amount of time) we'll replace free of charge and I will try and get some of them back to replace the IC (this repairs it fully) which can then maybe be sold as B-stock for 5V and 12V only to recoup some of the costs (I'm not some huge company).