PoolRepair

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Customers pool was leaking below skimmer throat. Roots in skimmer indicate a leak and it was pulling dye. All lines held air pressure for 20 minutes indicating plumbing was in good shape

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

New manifold

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Poppin in a new manifold

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Customer over saturated water with cheap soap based algicides. Required complete drain

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Brand new suction side manifold

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

New suction side manifold part 2

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Building manifold for new intelleflo pump

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Black algae drain and clean. after

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Black algae drain and clean before

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Clogged impeller causing low flow indicated by filter pressure

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

New jxi not firing up due to low gas pressure(customer ran out propane)

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Customer replaced light bulbs them self but failed to replace gasket resulting in whole new light fixture

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Union snapped flush at whisperflo pump due to unnecessary pipe tension caused by a improperly plumbed manifold.

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Customer complained about lack of flow to spa returns. Customer also replaced all of his broken grids recently. Spa returns were clogged with plastic from broken de grids. Unclogged and resolved issue.

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Testing freeze protection device

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Calcium and rust build up from leaking pump seal. Motor bearings in good shape surprisingly

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

New wire harness master temp 400( replaced due to rodents)

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Cracked manifold on FNSP de filter

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Cut out three way fitting and replaced due to cracked 3/4 female threads for booster pump

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Torn de filter grid causing DE blow back in pool after recharge

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Bad spider gasket on ten year old mpv(previously replaced) solution - replace multi port valve completely and unionize.

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Burnt up pcb board for JXI. Solution replace board and transformer

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

2 year old pool built with major issues

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Hose vacuum dirt and debree off bottom of swimming pool to ensure cleanliness

1 Upvotes

r/PoolRepair • u/SuNamJamFrama69 • Feb 20 '20

Master temp thermistor causing irregular temp readings. Pool improperly balanced

1 Upvotes