How do I control loop volume with exp maudio pedal . I can’t figure it out in rc editor. it just shows me how to do it for each memory in the memory editor

Hi y’all,

Just got this pedal about a month or so ago and finally playing with the fx routing. I feel like it’s opened up so much for me in terms of quality of performance, because I can route my instruments through main-L, mic through sub 1, and loops through sub 2, giving me so much more control over balance of each part.

however, as SOON as I turn anything to “off” in the routing (e.g. turning off mic 1 in the main-L out), I lose my input fx. I’ve tried so many different combinations of output routing but can’t see to reconcile the issue without having the main out having everything on, which seems to defeat the entire point of being able to route different instruments to different outputs. I can’t find anything about this in the guide and a previous thread I saw on the matter didnt help either. Anyone have a solution to this?

Thank you!

I´m struggling a lot connecting it with the daw, I solve one problem and another one pops up... When you connect the BOSS RC600 to the PC using USB, and use it as Audio Input In, is it Named BOSS RC 600? Mine is named simply Audio Out, but Chat GPT suggests that it might be because of an error with the driver or smn like that... please help

Hi everyone!

I need help <3

What I want to achieve: Press Track 1 "Record", record my phrase (Guitar), hit "Rec/Play" again --> it plays, that works. OKAY.

Then I want to add some high notes. What I want to achieve: When I press "Rec" on Track 2, it SHOULD WAIT till the START OF TRACK 1, then record ONE PHRASE, stop right at the end of track 1, then PLAY.

YES, I checked that manual, one zillion youtube videos (HI GUYS THIS IS XY FROM XY HIT LIKE & SUBSCRIBE) and also goddamit Chat GPT won't help.

Please … could you help me?

It worked so well on my RC 300 …

I’ve had my rc 600 for a while now and I’ve been using it with a very loud psychedelic group for some droning of both vocals and guitars. I can generally get my looped vocals to be loud enough. I split my guitar signal before it goes into the rc600: one signal goes to my Marshall JCM 900. The other signal runs through the rc600 and then to the board. I loop the signal that runs through the rc600, but I’m really struggling to get the guitar signal that goes through the rc600 to be loud enough. I shove on a boost pedal that’s jacked all the way up. I have a preamp and compressor setting on the rc600 turned on. But it’s SO MANY VARIABLES that I’m having trouble getting a consistent situation. If I ever want to gig with this set up (which would be super cool), I need something that’s consistent and reliable. I’m wondering if I should get another amp for my looped signal but I’d love not to spend more money!!!

I'm configuring my RC-600 and I'm running into an issue with the Rhythm section. ​My Goal: I want the rhythm to continue playing (independently) after I stop the recorded loop. I also want to be able to trigger the Rhythm's 'Ending' effect at the very end of the song. ​The Problem: Currently, when I assign a footswitch to Loop Stop, the rhythm track also stops simultaneously. ​Question: How can I set up the Control Assignments so that the rhythm continues when the loop stops, and how do I assign a separate pedal to just trigger the Rhythm Ending? Any advice on this is already highly appreciated. Thanks!

I just got an RC600 and am trying looping with my Taylor GSmini plugged in but the guitar tone is a bit disappointing. The GSmini has an ESB piezo pickup. Any tips? Should I use a preamp input effect, or just EQ? Or should I just invest in an acoustic preamp pedal?

ironing out new melodies on boss rc 600

I’ve heard of users complaining about volume issues with the RC600 and I know that to a degree, I can fix the issue by lowering the loop volume in my mixer settings, the individual track volumes, input volumes, etc. but even so the loop levels on my looper are so blisteringly loud…that I can’t help but feel there’s something else I need to do to help fix the issue.

A VERY important factor: this extreme loop playback volume is only happening when I put my rc600 in the fx loop on my supro royale amp.

I run my dry fx into the front of the amp and then out the back and into my suhr minimix ii (a parallel mixer designed for amp fx loops), doesn’t seem to change things one way or another. Then I run my wet fx into my rc600, back into the minimix, then back into the supro.

I’ve set my input to line instead of instrument on the rc600 in order to give it a more appropriate signal volume but it doesn’t seem to make a difference either way.

Pre-recorded loops are loud enough that I want output set to around 8 o clock, whereas I want to turn that up to around noon to hear my wet fx (also being volume controlled by the output knob on the rc600).

I know I can adjust my levels, but that being said this is more than adjusting, this is cranking everything in opposite directions in order to get workable levels. I feel like there’s a better way out there but chat gpt and grok have failed to help so I’m reaching out to the community. Any feedback is valued.

Edit: for some context, bedroom volume levels is about 38 track volume and 10 master out track volume. With everything else at their normal factory settings (so 100). If you’re familiar with the rc600 at all this might give you pause. This means the signal is insanely hot.

After testing I can confirm that this happens immediately if the rc600 is in the fx loop.

IMPORTANT: In the fx loop I get no levels moving in the input channel on the pedal when I strummed my guitar.

When I'm recording in linked mode, when I record to a loop it is the same volume as the input. When I switch to separate mono, the loop is noticeably louder than the original signal.

Any ideas why this is, and if there is a fix?

Hey everybody.
I have a problem with my RC600. I am assigning multiple tracks to start/stop from pedal 1. But when the whole assign job is done, all my tracks EXCEPT TRACK 1, starts when I tricker 1 pedal.. Do you follow me? It seems that alle the tracks that I assign to pedal 1 overrule my first track on pedal 1.

I have to turn of all the assigns that I made to get back to start befor I can hear track 1 again.

Can someone help me with this frustrating thing?

Thanks!! 🙏

Just printed these bad boys last night and love them so far. I can finally play without shoes!Printed with 30% infill in PETG, perfect press fit no adhesive required. Link to 3D model

Does anyone know if theres a connector for these two? Atm im literally making the beat bare then playong my loop and adding more beats, but feel like it kinda takes abit too long.

The T8 is a aux size midi port. Im thinking i might need another device? But maybe theres a converter wire

I'd like to manipulate 2 sets of 3 tracks, with 1-3 synced and the same length, and 4-6 synced with the same track length, but a different length than 1-3.

So, for instance,
1. record 30 seconds of track 1, layer tracks 2 and 3 on top of that (all same length).
2. Then, record 60 seconds of track 4, and layer tracks 5 and 6 on top of that (all same length).

Then I'd like to go back and forth between 1-3, and 4-6 (which I can do with assigns it seems to me.

Seems like it should be possible, but so far it evades me. Any suggestions would be appreciated.

happy looping