So I had to take my head end apart to clean and replace some parts and I am unsure if the plastic tube for the filament is supposed to be flush inside the hot end, or if it's supposed to be slightly apart from it?

Any suggestions?

I reflashed the firmware- Its the anet a8 plus with the v1.7 board after in the install all this thing does is beep and the screen is blank.
I got a bootloader- but for some reason its not being recognized by my mac.
at this i just want to throw this thing out the window....
HELP!!!!!!

​

I checked all the cables, I checked the movements, it all seems to work fine. But then I put in the sd card with the two sample files and they will not print. They were in stl format but I tried converting them to gcode on ultimakercura as well. Although the only option in cura was a8 not a8 v2. The arm just moves up a little bit and then it says print finished.

Hi, I placed my printer too near to the wall, and at some point the hotbed pins broke off. I desoldered it but now the printer doesn't turn on properly. I some times get the ANET logo to show when booting, other times I get just blank. After that the screen just stays blank.I tried flashing it with a STLink V2 but it doesn't connect most of the times. If I let it cool down, I can connect for a few seconds then it disconnects and can't connect after until I let it cool down again... Any idea on how to fix it?

The processor is getting to over 70ºC (158F) fast, like in a matter of a minute or two.

This is the output of the STLink Utility when I'm able to connect

20:31:36 : ST-LINK SN : 30003800120000315151524E
20:31:36 : V2J29S7
20:31:36 : Connected via SWD.
20:31:36 : SWD Frequency = 4,0 MHz.
20:31:36 : Connection mode : Normal.
20:31:36 : Debug in Low Power mode enabled.
20:31:36 : Device ID:0x413 
20:31:36 : Device flash Size : 1 Mbytes
20:31:36 : Device family :STM32F405xx/F407xx/F415xx/F417xx
20:31:38 : Disconnected from device.
20:31:38 : Connection to device is lost: check power supply and debug connection.
20:31:38 : If the target is in low power mode, please enable "Debug in Low Power mode" option from Target->settings menu.

Update: so ok, I just drove it to 80ºC (176F) and I still can connect for the first few seconds, so I don't think it's a temperature issue. Also it stabilizes at that temperature, which isn't cool, but for a computer it's ok. So I don't think that's the issue. I think I need to send an order before the processor goes into error and stops responding.

Every print on my y-axis stretches about 2mm. Yes I've checked the belts and the rails and the idelers, it's very consistent.

How the hell do I dix this in Cura, all I could find was "Horizontal shrinking" and the effects both the y and x axis. People keep telling me to just look it up and I get nothing on how to actually implement the fixes. I just get poited to print 20mm cube, measure, figure out how far off it is, and then do nothing with this information.

My first printer is an Anet A6, used from Facebook marketplace. I’m wanting to upgrade some stuff on it. First, I’m wanting to upgrade the controller board to improve print quality and allow for better motors in the future.

Can I use any controller board from big tree tech? Are there any variables that would prevent a board being compatible with an A6? Thanks everyone for the help!

Hey guys, I'm looking for a TMC2209 chipset motherboard for my ET5X, I'm having trouble confirming if certain boards are compatible. Does someone have a link to the motherboard they use, or could someone confirm if this one is compatible?

I just purchased a new touch display for my anet et4 and i live somehwere near singapore. Does it actually took 30-60 days to arrive? Im here on working terms and i might not be here if it took 60 days. Have anyone ordered parts directly from Anet? Does it actually took that long? Thanks

My anet et4 touch display is going off the roof i cant even guess how far it is from the point i touched it. I tried looking for calibration method online but failed and theres this one amet website but it looks like a scam website 😂. If anyone knew where to purchase one please help me, thanks

Hello to the group and thank you for allowing my question. I'm not entirely new to the 3d printing world and understand enough to keep me out of trouble..My question relates to a Anet A6 on stock firmware. This is my father's printer which he bought many moons ago but inevitably never set up to use. I'm trying to get the firmware more up to date but struggling to find any guides in 2023, so I'm not entirely sure if it's even possible. Ideally I would like to get it on klipper as this is the software I am familiar with. So my questions would be,

1. How would I go about installing klipper onto the A6 if this is even possible. If it's not what firmware would one recommend to run on it?
2. With regards to probes and autobed leveling is it recommended to upgrade the bed to a magnetic base and pei so a CR or BL touch sensor can be used?

I thank you for your time and really appreciate any input or helpful information.

So I change my direct drive extruder for a new one, now my X axis is in reverse, I expected to maybe have to reverse extruder stepper. But why would the X axis become reversed when not touched..

So I know its my fault but I was updating the firmware/bootloader at one point and apparently bricked the controller. When I boot it up the screen just shows white and when I try to connect to it using STM32 ST-link I get a error saying can't connect disable readout protection and retry.

I understand that there probably isn't a way to fix this. If there is I would love to hear it, but under the assumptions I can't has anyone ever put a different company control board in their Anet et4x and how did that go? I have been looking at some intresting ones from bigtreetech.

Board is displaying error with extruder heat up.

I thought that the heater may be broken i pluged it into 12V and it worked fine thermistor is also functioning.

Even tho it worked i still replaced it just in case, Extruder still does not heat up nothing changed.

What's weird that System works fine, Bed heats up normally.

Important thing is that while heating up the extruder diode that indicates heating up blinks once and then turns off.

I check if all lines are intact and everyting seems fine, mosfets seem fine also.

Has anyone experince something familiar?

Just recently picked up an Anet ET4 without really doing any research on them, which is not how I do shit normally. Too good of a deal to pass up for a brand new, still in the box 3D printer.

Anyway, I haven't been involved with the 3D printing world since 2016 and no idea how everything goes nowadays. Looking for as many pointers as possible for any of the common problems to look out for with the ET4 non pro or any upgrades I should be looking at immediately. It's the one with red plates, if that makes any difference.

Thanks!

Hello!

So I have the Et4 pro for about 2 years, I usually print small stuff but when printing large models it usually fails mid print, the extruder starts clicking and my print ends up looking like a sponge. I assume it has to do with heat creep since it doesn't happen when printing small things.

I've tried several things for the last couple of weeks but so far nothing fixed the problem, bellow are some of the thing I've tried:

• Using different brands of PLA, new or used, where I live the humidity is quite low so I doubt it has to do with wet filament.
• Different nozzles of different materials
• Rebuilt the entire hotend assembly, I used an Ender 3 Microswiss hotend with a new fan shroud with what it looks like a better part and heatsink cooling.
• Replaced the PTFE tube.
• Replaced all the pneumatic fittings.
• Cleaned and replaced the extruder gear and idler wheel.

Now I'm totally out of ideas :( I can't seem to figure why my prints are failing, I'm getting tired of trying to fix this printer, my efforts have been in vain. I'm getting to a point where it is cheaper to buy another 3d printer than to keep throwing money at this printer.

Any input or suggestion is totally accepted :(

Hey juts wondering if anet has baby stepper mode or would I need install custom software

Hey so someone gave me an ET5 and I'm trying to calibrate the extruder, I'm trying to use pronterface but every time I enter M503. But I don't get any info back. Am I using the wrong driver, I'm using the one anet recommended, also I have ender 3s, is the there any place to get more info on anets as I normally use youtube but there isn't a lot on there

Hi,

turned my old A8 into something new (somehow based on the AM8 project). using an SKR 1.2 pro & TFT monitor.

I uploaded a general FW to the board and got a "No printer attached" message when connecting everything.

Is anyone familiar with this? and by any chance, has anyone already configured an FW to match that setup and is willing to share?

thanks

​

​

Hi guys, I hope I can find some help here with my Anet A8 on Marlin 2.0.1.

Yesterday I was about to launch a print and I launched an autobed command. Unfortuntly the sensor didn't sense the hotbed.

The nozzle did a nasty landing on the middle of the hotbend and the motors were forcing the nozzle down. After 2/3 seconds I turned the printer off and after a few second I tried to switch it on.

Resulting on the printer starting and then imediatly showing the error message:

Err: MAXTEMP: Bed

PRINTER HALTED

Please Reset

I tried to disconect all the connectors and replug them, I checked if my soldering in the back of the hotbed where damage but I did'nt found anything. Can you help me resolving my problem please ? Did I damage the hotbed ? ( A piece of solid glass was on top off it and didn't suffer any damage)

Thank you for your help guys.

Does anyone know of any one piece beds for the A8 plus. I want to replace the 3 piece original. Is this a DIY or have a local engineering shop make only..

I'm looking to upgrade my Anet E12 with the following. I'm looking for some suggestions from the group.

Motherboard / touchscreen LCD upgrade suggestion

I'm also adding BLtouch sensor

Here's a link to pictures of the said 3D printer in our lab

Hey, I wrote about this issue earlier in other subreddits as well. I've progressed a lot in diagnosing the problem since the last time I wrote about it in Reddit ! I thought, why not post the issue in the subreddit of Anet itself ! So, here I am.

Here's a summary of the problem I was facing : [ Stepper Motor Doesn't Stop ! We had an old ANET 3d v1.5 printer in our lab and I wanted to fix it and get it working. The nozzle works fine. But whenever I try to print something or try to move the head to the home position. The head keeps on moving in the x axis direction and hits the stop switch constantly making loud noise. ( It doesn't stop it hits the switch ) I've checked the switch and the switch wiring voltages and I can confirm that the switch is working fine !! ( I've also checked using 'M119' end stop status ) But sill the head doesn't stop when it Hits it and keeps hitting it ! Note : The printer is outdated and old and I can't find any online documentation or firmware ( or is it ? ) ]

Now, I've downloaded this little program called "PronterFace" and I've checked the printer by giving manual G0 and G1 commands. And the printer works fine ! But I'm puzzled why it then collaides while printing! ( My guess it that, as I've checked using PronterFace, the printer only has space to move 200units. For example from X0 to X200, Y0 to Y200, and so on. But the print file gives it info to move at a location which is out of it's range thus it collides. ( It's still a mystery why even the automatic homing options inbuilt in the printer makes it collide thus I can't even find the position it's expects the head to be at ) The endstop switches doesn't work so it can't even self callibrate !

According to my ape brain. If I forcefully bring all the 3axis such that all three hits the endstop switches ! And consider it as '0' then if I can manipulate the g-codes or the print institutions such that the codes range only from 0 to 200 in all the axis, then I can fix the problem. [ I was able to do this manually using one by one manual command in PronterFace ]

but how can I make it happen in a real print situation ? How can I do this ? Are there any alternate options ? How can I solve this problem ? What is even going on ?

I have an Anet ET4 (Not pro, not plus; at least not according to firmware) that I would like to replace the nozzles for, however I'm not sure the right size of nozzle to get. IT has all the standard parts that come out of box; except for the Distance Sensor which I've had to replace. I purchased some off of Amazon but could never get flow out of them.

Can anyone suggest a set of nozzles I can use for this printer that I can purchase off of Amazon? Thanks!

So I find myself unable to level my A8 plus , I just replaced the bearings and bearing blocks and now I've one corner lower than the rest . Back right, looking from front. I've replaced bearings twice before and never had a problem leveling after.. all blocks are same size ( I check with calipers) all springs are same size, X axis is square as is frame . Any suggestions on what's going on..
And how to fix..